fbpx

How To Install Asphalt Shingles On a Roof

by | Oct 15, 2021 | Blog | 0 comments

Installing Asphalt shingles may be a time-consuming and complicated operation. Asphalt shingles typically need to be cut to the proper size before they can be placed. This method necessitates the participation of a large number of people and the expenditure of substantial time.

Installing asphalt shingles on a roof is a fun activity that may go wrong. So, take safety precautions, remove old shingles, measure the required size of shingles, and install roof flashing and underlayment. Ensure to follow the fundamental instructions such as pipe and vent safety. If you’re not satisfied doing it yourself, you may hire an expert.

A little bit of experience is required for installing asphalt shingles on your home’s roof properly. Even if you have previous expertise with asphalt shingles installation, it might not be easy to do on your own. In addition, you must ensure that you are employing the proper instruments for the job.

Here are a few tips for how to install asphalt shingles on a roof.

What Is The Best Way To Lay Asphalt Shingles On a Roof?

Installing new shingles on your own may save you a significant amount of time and money. You may get the same professional appearance by following the same methods as they do. Replacement of your roof’s shingles is a smart way to keep your home in good condition while keeping your family safe and protected from the elements.

Learn how to properly prepare a roof for shingles, lay even courses of shingles, and install your ridge shingles the way the pros do it.

1. Take Safety Precautions

Working at heights, such as on a roof, poses a danger of falling and raises additional safety considerations. Only competent experts familiar with the best shingling roof should work on roofing as they have received comprehensive training in all elements of roof construction safety.

Furthermore, it is critical to check any applicable building rules in your area and ensure that your roof complies with all of them.

2. Remove the old shingles

It isn’t easy to correctly install extra flashing and underlayment if the old roof does not replace before installing the new ones. It is vital to remove all the old screws or pound them flat before taking off the old shingles and starting again.

Holes would be created in your new shingles by nails that protrude through their surface. If you have transportable things near your house and are afraid that they may be damaged, you should think about moving them. Spend some money on several giant tarps to shield your plants and landscape from the pounding rain and to capture the hundreds of nails that will fall from the roof.

  • Facebook
  • Twitter
  • Pinterest
  • Gmail

3. Calculate the Single You need for Your Roof

In most cases, the requirement is three packages of shingles to cover 100 sq ft of ground. Asphalt shingle “packages” are sealed packets of asphalt shingles. Take accurate measurements of your roof and purchase the necessary materials.

Measure the entire width and length of the different parts of the roof, and multiply them to get the total area of the roof structure. To acquire the correct number of squares, add the areas of each part together and divide by a hundred to get the appropriate number of squares. To get the number of packages you’ll need to purchase, multiply this amount by three.

4. Install the Roof Flashing

Flashing is necessary for each valley and any location where one roof component flows into another element at 90 degrees. Roll out the flashing in these parts and secure it with roofing nails around the outer borders, leaving the middle empty of any nails.

A nail close to the center of this flashing may cause leaks to appear through your roofing material. You must remember to put roofing cement below each line of shingles near the valley flashing while placing the shingles around the flashing.

When the roof meets a residence wall, such as rooflines or a multi-tiered roof, it is best to put the flashing to keep the area protected from the elements. Also, built the flashing around fireplaces and sunroof windows to keep them protected from the elements.

5. Install the Roof Underlayment

After installing the flashing:

  • Prepare the roof for shingles.
  • Install a drip edge, an ice and water barrier, and an underlayment to achieve this.
  • Peel and stick sub floor First, staple or nail the ice and water underlayment along the roof line, folding it down and over the face edge of the roof by an inch or two.

After installing the ice and water barrier along the roof’s lower edge, nail the drip edge’s upper face to the ice barrier, overlapping the drip edge at the seams to create a continuous protective surface. Install the drip edge and ice and water barrier at the bottom before putting the underlayment.

To install the underlayment, spread it out over the drip edge and secure it with cap nails distributed evenly across the roof. Bring the cap nails 4 inches apart down the underlayment’s lower edge, but avoid nailing further into the drip edge on the first pass.

Install the underlayment in rows, overlapping each row by at least 6 inches, until the roof is completely covered on each side, just below the ridge. Install a ridge of felt paper that splits in the middle and comes down to cover and overlap the underlayment on each side. Finish with a drip edge along the roof line sides over your underlayment. Now it’s time to put the shingles.

  • Facebook
  • Twitter
  • Pinterest
  • Gmail

6. Installing the Asphalt Shingles

Begin by nailing down a row of initial shingles along with the asphalt shingles lower border of the roofline. Lay a set of starting shingles along the roof’s sides, ensuring they overhang the starter shingles put at the bottom.

Install four to five or six nails through each shingle below the tar border but above the dripping edge of the first row of shingles. Do this on both sides of the roof, then add ridge cap shingles on top. Begin on the left side of the ridge and work your way right.

Place the second cap shingle over the first and nail it in the same way on the left. Follow this to the roof’s edge. Seal the last cap shingle nail with roofing tar to keep water out.

7. Pipe and Vent Safety

As you install your shingles, make sure to place rubber boots around any vents and pipes. In this case, the lower flashing goes on top of the shingles, and the higher flashing goes below them. On the sides, it is necessary to fasten the flashing under the shingles. It permits water to travel down the shingles, over the flashing, and out of your home.

Following these instructions precisely will teach you how to install roof shingles.

  • Facebook
  • Twitter
  • Pinterest
  • Gmail

Wrapping it Up

After the installation, keep a watch on your property for a few months. Look for evidence of roof leaking and areas of the roof that appear to be flapping or blowing up excessively.

A homeowner may install a shingle roof on their own, but it is not a simple task. It’s something you must first comprehend and analyze. If you are unsure of your talents, it is preferable to hire an expert remodeling contractor than to risk making a mistake.

 

RELATED POSTS

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *

Pin It on Pinterest

Share This

Share this post with your friends!

Share This

Share this post with your friends!